Inovance Inovance SV660N EtherCAT servo drive
- E101.0 — E101.0 — parameter error in H02 and above
- E101.1 — E101.1 — parameter error in group H00/H01
- E101.2 — E101.2 — Address error in read/write operation after the number of parameters
- E101.9 — E101.9 — Parameter attribute initialization check error
- E102.0 — E102.0 — FPGA communication establishment error
- E102.1 — E102.1 — FPGA initialization start error
- E102.8 — E102.8 — FPGA and MCU version mismatch
- E104.1 — E104.1 — MCU running timeout (MCU break down)
- E104.2 — E104.2 — Current loop operation timeout (FPGA break down)
- E104.4 — E104.4 — MCU command update timeout
- E108.0 — E108.0 — Parameter write error
- E108.1 — E108.1 — Parameter read error
- E108.2 — E108.2 — EEPROM write check error
- E108.3 — E108.3 — EEPROM read check error
- E108.4 — E108.4 — frequent single data reading
- E111.0 — E111.0 — Internal parameter error
- E120.0 — E120.0 — Unknown encoder model
- E120.1 — E120.1 — Unknown motor model
- E120.2 — E120.2 — Unknown drive model
- E120.3 — E120.3 — The motor and drive do not match in the power
- E120.5 — E120.5 — Motor and drive current mismatch
- E120.6 — E120.6 — FPGA and motor model mismatch
- E120.7 — E120.7 — Model check error
- E120.8 — E120.8 — Junction temperature parameter check error
- E121.0 — E121.0 — Duplicate S-ON command
- E122.0 — E122.0 — Multi-turn absolute encoder setting error
- E122.1 — E122.1 — Different DIs assigned with the same function
- E122.2 — E122.2 — Different DOs assigned with the same function
- E122.3 — E122.3 — Upper limit in the rotation mode invalid
- E136.0 — E136.0 — Encoder ROM motor parameter check error
- E136.1 — E136.1 — Encoder ROM motor parameter read error
- E136.2 — E136.2 — torque ripple compensation data check error
- E140.0 — E140.0 — encryption chip check error
- E140.1 — E140.1 — MCU key calculation failed
- E140.2 — E140.2 — wrong encryption chip version
- E140.3 — E140.3 — Encryption chip damaged
- E150.0 — E150.0 — STO safety state applied
- E150.1 — E150.1 — STO input state abnormal
- E150.2 — E150.2 — Buffer 5 V voltage detection error
- E150.3 — E150.3 — STO input circuit hardware diagnosis failure
- E150.4 — E150.4 — PWM buffer hardware detection failure
- E201.0 — E201.0 — Phase-P overcurrent
- E201.1 — E201.1 — Phase-U overcurrent
- E201.2 — E201.2 — Phase-V overcurrent
- E201.4 — E201.4 — Phase-N overcurrent
- E208.2 — E208.2 — Encoder communication timeout
- E208.3 — E208.3 — Current sampling fault
- E208.4 — E208.4 — FPGA current loop operation timeout
- E210.0 — E210.0 — Output short-circuited to ground
- E220.0 — E220.0 — Phase sequence incorrect
- E234.0 — E234.0 — Runaway
- E320.0 — E320.0 — Regenerative resistor overload
- E400.0 — E400.0 — Main circuit overvoltage
- E410.0 — E410.0 — Main circuit undervoltage
- E410.1 — E410.1 — Main circuit de-energized
- E420.0 — E420.0 — Main circuit phase loss
- E430.0 — E430.0 — Control circuit power supply undervoltage
- E500.0 — E500.0 — motor overspeed
- E500.1 — E500.1 — Speed feedback overflow
- E500.2 — E500.2 — Velocity feedback error 2
- E600.0 — E600.0 — Inertia auto-tuning failure
- E601.0 — E601.0 — Homing warning
- E601.1 — E601.1 — Homing switch error
- E601.2 — E601.2 — Homing mode setting error
- E602.0 — E602.0 — Angle auto-tuning failure
- E602.2 — E602.2 — U/V/W phase sequence reversed
- E605.0 — E605.0 — Motor speed too high upon S-ON
- E620.0 — E620.0 — Motor overload
- E630.0 — E630.0 — motor rotor locked over-temperature
- E640.0 — E640.0 — IGBT over-temperature
- E640.1 — E640.1 — Flywheel diode overtemperature
- E650.0 — E650.0 — Heatsink overtemperature
- E660.0 — E660.0 — Motor overtemperature
- E661.0 — E661.0 — STune failure
- E662.0 — E662.0 — ETune failure
- E663.0 — E663.0 — ITune failure
- E664.0 — E664.0 — Resonance too strong
- E730.0 — E730.0 — Encoder battery warning
- E731.0 — E731.0 — Encoder battery failure
- E733.0 — E733.0 — Encoder multi-turn counting error
- E735.0 — E735.0 — Encoder multi-turn counting overflow
- E740.0 — E740.0 — Absolute encoder communication timeout
- E740.2 — E740.2 — Absolute encoder error
- E740.3 — E740.3 — Absolute encoder single-turn calculation error
- E740.6 — E740.6 — Encoder data write error
- E760.0 — E760.0 — Encoder overtemperature
- E765.0 — E765.0 — Nikon encoder over-temperature or overspeed
- E900.0 — E900.0 — DI emergency braking
- E901.0 — E901.0 — invalid stop mode
- E902.0 — E902.0 — DI setting invalid
- E902.1 — E902.1 — DO setting invalid
- E902.2 — E902.2 — Invalid setting for torque reach
- E902.3 — E902.3 — invalid position comparison target
- E908.0 — E908.0 — Model identification failure
- E909.0 — E909.0 — Motor overload warning
- E910.0 — E910.0 — Control circuit overvoltage
- E920.0 — E920.0 — Regenerative resistor overload
- E922.0 — E922.0 — Resistance of the external regenerative resistor too small
- E924.0 — E924.0 — Regenerative transistor overtemperature
- E939.0 — E939.0 — Motor power cable disconnected
- E941.0 — E941.0 — Parameter modifications activated at next power-on
- E942.0 — E942.0 — Parameter saved frequently
- E950.0 — E950.0 — Forward overtravel warning
- E952.0 — E952.0 — Reverse overtravel warning
- E980.0 — E980.0 — Encoder algorithm error